In this
guide, we are going to look at how to polish your shoes
(or boots) properly. Keeping your appearance above 100%
will never hinder your ATC cadet career, and having
perfect, shiny shoes will make you stand out from the
rest of the cadets as someone who cares about their
uniform and wants to achieve something in the ATC.
The method I am going to describe to you is standard
polishing, very similar to the “spit and polish” method.
To polish your shoes properly, you will need the
following items:
 |
- You (should polish
your shoes yourself, don't get mummy or
daddy to do it for you)
- Kiwi Shoe Polish
(Black) – I recommend you use Kiwi; it's the
best polish around. You may also want to buy
Kiwi Parade Gloss as it is good for getting
a nice deep shine.
- A duster, soft rag or
cotton wool. – What you will be polishing
with. If you use cotton wool I recommend
that you use pads rather than cotton wool
balls. (And if the rag isn't soft it will
scratch the surface of your shoe and you
will be doing more harm than good.
- Water – in a bowl,
cup, whatever. Some people will use warm
water because it helps to work the polish
into a nice smooth shine, but if the water
is too hot it will melt the polish off your
shoe and you will have to start again.
|
 |
Once you have these items
you are ready to polish. Be warned, Polishing
will take hours, literally, at the beginning, a
good pair of shoes is not something that can be
achieved in 20 minutes. It will take you hours
to get your shoes up to a high standard, and
yes, it is quite hard, but follow this guide and
you can't go wrong.
To begin with, you must make sure your whole
shoe is free of mud and dust. Pick up your
duster and wrap it around your index finger so
that the cloth on the top of your finger is
smooth and has no creases. If you are using
cotton wool pads, fold it in half, and in half
again, polishing with the straight part.
Next we need to wet the cloth. Dip your index
finger into the bowl of water, so the top part
of your finger is wet. Squeeze of any excess
water. If you are using a cotton wool pad, dip
that in too. |
 |
Now we need to get some
polish onto the shoe. Gently rub the cloth or
piece of cotton wool along the shiny surface of
the polish. You are aiming for something like
this:
Now we are ready to start.
Gently rub the polish into the toe cap of your
shoe in circular motions, covering the complete
toecap, including the sides. Keep repeating
these circular motions until all the polish has
disappeared and does not smear when you rub over
it. If the surface of the shoe becomes dry, wet
the duster or cotton wool again.
When you first start polishing, you will feel
that the surface is rough. You will need to
repeat the process above until the surface of
the shoe is smooth, and remember to use plenty
of water. |
 |
The circular motion is a
vital part of the process. The motion works the
polish into the shoe and allows the polish to
settle onto the surface of the shoe.
By now, you should have a
smooth surface. Compare your polished shoe to
your unpolished shoe. You should be able to tell
between which has been polished, and the
polished shoe should be much darker than the
unpolished shoe.
Now it is time to finish your toecap. It is
basically the same process as above, but with a
few small changes. This time we will use only a
small amount of polish and a little more water.
These “small” layers should only take about 30
seconds to apply, and you will need to apply
only a few of these layers to attain a shine. |
|
Many people with good, polished shoes will not
stop at the toecap. Some people polish the
complete shoe, even the underneath. Before an
inspection, If you wish to do this you will need
to put one small layer of polish onto the rest
of the shoe, including the rims (welts) of the
shoe. The polishing method is exactly the same,
but do not use lots of polish, use only one
layer, otherwise there will be no distinction
between the toecap. Here are some photos of a
shoes being polished all over. |
 |
 |
|
Congratulations!! Now you should have a decent
polished shoe. Repeat the process for the other
shoe and make sure you spend the same amount of
time on each shoe.
You should aim to get your
shoes looking like this: |
 |
 |
But it does not end there. You
will need to maintain your shoes. If you do not maintain
them they will loose their shine. To maintain them,
simply put a few small layers of polish on your shoes
before and after you wear them. If you do not do this,
you will have to spend hours polishing your shoes in the
future. It is easier and simpler to keep them in a high
standard all the time.
Remember to always work on your shoes, as I said it is
not something that will happen over night, you must keep
at it. It is worth it to have shiny shoes.
Top
Tips:
- Do not cheat! There are
people out there paint or varnish their shoes. Do
not attempt this, your CO will know if they are not
properly polished.
- At camps, and other places
where cadets meet, you will probably hear some weird
methods of polishing, which include using household
objects such as spoons and irons. DO NOT USE THESE
METHODS. These methods are probably also hard to
use and will probably mess up your shoe if you do
not possess the skill to use the method. It is
risky, do not take the risky path, use the one which
you know and you will get to your target eventually.
- Do not use any instant shine
pads. They will leave your shoes oily and your shine
in your shoes will get really dull after a while, it
simply isn't worth it.
- Replace your cotton wool and
water regularly.
- Store your shoes in a box
somewhere where they cannot get filled with dust
Stripping your shoes
This means getting all the polish
off your shoes, maybe you dropped something on to
your toecap which left large dents in the polish,.
Before you “strip” your shoe you should do everything
you can to try to save the mistake, only use this as a
last resort.
There are various methods of stripping shoes, the
easiest is the one I will now describe.
For this you will need:
- Hot water – but please do not
scold yourself, health & safety risk, and it hurts.
- A rough cloth, maybe an OLD
t-shirt.
Place your rough cloth into the
water being careful not to scold yourself. Rub the cloth
along the shoe. You will need to be vigorous in order to
remove the polish from the shoe. You will also need to
replace the cloth every so often in order to get the
maximum effect from the method. Some people may use MILD
house cleaners to help the polish come off, but I do not
know the effectiveness of this as I have never tried it
before, I suggest that you stick to using just hot
water.
Remember, maintain your shoes and polish them before
each time you wear them.
Remember, wear your uniform with pride.
|